Water system

Oakwood Village MHP

EPA ID OH5703715 · Montgomery County · 1,500 people served

Great Miami Buried Valley Aquifer wells (recharged by Great Miami & Mad Rivers)
Groundwater

Oakwood Village MHP buys its water from Montgomery County Water Services 2.

The system's record

Great Miami Buried Valley Aquifer wells (recharged by Great Miami & Mad Rivers)
Groundwater
Oakwood Village MHP buys its water from Montgomery County Water Services 2, which buys from Dayton Public Water System. Dayton Public Water System treats groundwater from Great Miami Buried Valley Aquifer wells (recharged by Great Miami & Mad Rivers).
Wells: EPA lists 105 active wells. ODNR well logs locate 4 public-supply wells inside Dayton Public Water System's wellhead protection zone, 120 to 162 ft deep, in sand & gravel and sand & boulders. Zoom in to see them as dots.
Well 36Well 57Well 58Well 1Well 3Well 6Well 7Well 8Well 13Well 17Well 20Well 21Well 22Well 23Well 24Well 25Well 26Well 27Well 28Well 29Well 30Well 31Well 32Well 33Well 37Well 4RWell 9RWell 15Well 10RWell 11RWell 12RWell 14RWell 15RWell 16RWell 2Well 6Well 7Well 8Well 9Well 10Well 11Well 12Well 13Well 14Well 15Well 16Well 17Well 18Well 19Well 20Well 21Well 22Well 23Well 25Well 26Well 27Well 30Well 31Well 33Well 37+45 more
Aquifer
Great Miami Buried Valley Aquifer
Water bodies
Great Miami River, Mad River
Raw intakes
Dayton Miami
Dayton Mad River
Active wells
105
Serves
141,407 people · Montgomery County
EPA ID
OH5703512

About this area's water Dayton Public Water System

Mouth of the Mad River at the Great Miami River in Dayton, Ohio, source of the Mad River Well Field aquifer recharge
Mouth of the Mad River at the Great Miami River in Dayton, Ohio, source of the Mad River Well Field aquifer rechargePhoto: Antony-22, CC BY-SA 4.0 · Wikimedia Commons
Did you know
  • The Great Miami Buried Valley Aquifer holds more than a trillion gallons and is the principal water source for an estimated 1.5 million people in southwest Ohio.
  • Dayton recycles its own softening waste: a Lime Recovery Facility recalcines lime sludge from both plants back into usable lime, 36,533 tons of it in 2021.
  • Each of Dayton's two plants is rated at 96 million gallons a day, yet the city pumped about 24.35 billion gallons in all of 2025, roughly a third of that capacity.
  • Dayton's 1870 waterworks used a Holly system, an early direct-pumping fire-and-water design; it started up March 31, 1870, after voters approved it in 1869.
History5
  • 1869-1870Dayton voters approved a municipal waterworks in 1869; a Holly direct-pumping system began operating March 31, 1870.
  • 1929Dayton's Division of Water Reclamation began continuous operation, treating sewage before discharge to the Great Miami River.
  • 1988U.S. EPA designated the Great Miami Buried Valley Aquifer, Dayton's sole water source, a Sole Source Aquifer in May 1988.
  • 2016In April 2016 Dayton took production wells near Tait's Hill out of service over PFAS suspected from the city's own Fire Training Center.
  • 2021The city sued Wright-Patterson Air Force Base and the Pentagon over PFAS contamination of its groundwater.
Treatment & pressure

How it is treated

Conventional lime (calcium oxide) softening, then pH adjustment with carbon dioxide, fluoridation, chlorine disinfection, and rapid sand filtration as the final step. A Lime Recovery Facility recalcines softening sludge from both plants back into usable lime.

Water pressure

Not published. Dayton runs 2 main and 11 booster pump stations and 16 storage facilities holding 88 million gallons, implying several zones, but no psi figure.

What it costs

$5.97 per 1,000 gallons

Effective Jan 1, 2026: $44.67 per 1,000 cubic feet on the first block, which is $5.97/1,000 gal, plus an $18.60 monthly minimum for a 5/8-inch meter.

Water quality & impurities7
ContaminantLevelLimitYear
PFOS (finished water, Ottawa plant)
Average of monthly finished-water samples; range 5.45-13.67 ppt, above the 4 ppt MCL.
8.81 ppt42025
PFHxS (finished water, Ottawa plant)
Range 6.70-23.32 ppt at Ottawa, above the 10 ppt MCL; Miami plant was below 2 ppt.
13.53 ppt102025
PFOA (finished water, Ottawa plant)
Range under 2.0 to 4.5 ppt; average below the MCL. Miami plant non-detect.
2.97 ppt42025
Lead (90th percentile)
0 of 54 samples above the action level; lead was not detected in most samples.
<3.0 ppb152023
Copper (90th percentile)
0 of 54 samples above the 1.3 ppm action level.
0.044 ppm1.32023
Total trihalomethanes (TTHM)
Highest running annual average in the distribution system; range 17.9-41.5 ppb.
28.83 ppb802025
Nitrate
Highest at the Miami plant; Ottawa reached 1.44 ppm. Well under the limit.
1.71 ppm102025

EPA compliance record · Oakwood Village MHP

Lead at the tap: 90th-percentile result 0 ppb in 2025 (action level 15 ppb).

EPA health-based violations since 2015:

  • 2024Lead and Copper Rule Revisions · lead service line inventory missing or incomplete (a records requirement, not a lead test result) · returned to compliance

5 violations of any kind logged since 2020: 1 for required testing that was missed or reported late; 3 for a report, record or notice that was missing, late or incomplete (the yearly water quality report, a public notice, lead line records); 1 health-based.

EPA compliance record · Dayton Public Water System (treats the water)

Lead at the tap: 90th-percentile result 0 ppb in 2023 (action level 15 ppb).

EPA record: no health-based violations since 2015.

Projects & plans6

Recent and current work

  • Lime Recovery Facility recalcination · 2021 · completed
    Reclaims lime from softening residuals at both plants; produced 36,533 tons of recovered lime in 2021.
  • Tait's Hill production well removal · 2016 · completed
    City proactively took wells near its Fire Training Center out of service over suspected PFAS contamination.
  • Renewable natural gas from digester biogas · 2024 · completed
    Since November 2024 biogas from the Water Reclamation Plant's anaerobic digesters is cleaned and injected into gas pipelines.

Planned or needed

  • PFAS removal facility and treatment plant retrofit · 2024 · planned
    City estimates $300M-$500M for PFAS remediation and management; a Shook contract is reportedly about $350M.
  • PFAS treatment pilot and plant upgrades · planned
    EPA pilot treatment project underway; part-funded by 0% Ohio EPA loans with principal forgiveness the city says will not raise water rates.
  • Wright-Patterson AFB remediation request · 2024 · proposed
    An October 2024 letter asked the base to remediate PFAS; the city had already sued the base and the Pentagon in 2021.
Supply stress

PFAS from firefighting foam is the binding constraint: Ottawa plant finished water averaged 8.81 ppt PFOS and 13.53 ppt PFHxS in 2025, over the 4 and 10 ppt MCLs. Quantity is not a concern - the aquifer holds over a trillion gallons and is river-recharged - but treatment will cost hundreds of millions.

Sewers

Sanitary

Dayton's Division of Water Reclamation has run continuously since 1929; the plant is rated 72 MGD and discharges to the Great Miami River at river mile 76.1, serving about 340,000 people including parts of Greene County and Wright-Patterson AFB. About 765 miles of sanitary sewer.

Storm

A separate MS4 storm system of over 400 miles of storm sewers, run by the city's Sewer Maintenance Bureau alongside 28 pumping stations. No stormwater utility fee was found published.

Sourcesverified

Compiled from the utility's own reports and public records, then independently re-checked against primary sources.

Present in 1 ZIP code

Serves

No ZIP code has Oakwood Village MHP on record as its main water supplier.

Also present in 1 more ZIP code

Population-weighted resident shares; a ZIP code can have more than one system on record. Recomputed from each ZIP's own system list, not from the map's cached footprint.

Buys from · Sells to

Oakwood Village MHP buys its water from Montgomery County Water Services 2, which buys from Dayton Public Water System.

No other system is on record buying water from Oakwood Village MHP.

What the records show about Oakwood Village MHP

Who runs it

EPA's record says Oakwood Village MHP has 511 service connections and serves 1,500 people.

EPA classes it as a community water system, one that serves the same residents all year.

Its office telephone on EPA's record is 231-280-5835.

Source: EPA Safe Drinking Water Information System (SDWIS), water system record.

How the water is treated

Oakwood Village MHP buys water that Dayton Public Water System treats first, so the steps that count are the seller's. EPA's treatment table registers these steps for Dayton Public Water System: corrosion control, coagulation and settling, chlorine disinfection, fluoridation, lime softening, and sand or media filtration.

The list is what each system registered with EPA for treatment plants EPA still shows as active, and it can lag a plant upgrade.

Source: EPA Safe Drinking Water Information System (SDWIS) treatment table (EPA Envirofacts, pulled September 2026).

Violations

EPA counts 1 health-based violation for Oakwood Village MHP since 2015. Health-based means a contaminant above its legal limit or a required treatment step not carried out. It falls into 1 separate problem (one contaminant or rule in one year); the table lists it.

EPA logs 5 violations of any kind since 2020: 1 for required testing that was missed or reported late; 3 for a report, record or notice that was missing, late or incomplete (the yearly water quality report, a public notice, lead line records); 1 health-based.

Health-based violations since 2015, most recent first
YearContaminant or ruleKindMeasuredLimitStatus in EPA's record
2024Lead and Copper Rule Revisionslead service line inventory missing or incomplete (a records requirement, not a lead test result)not on filenot on filereturned to compliance

Source: EPA Safe Drinking Water Information System (SDWIS) violation records: health-based violations with compliance periods beginning in 2015 or later, all violations from 2020 or later (EPA Envirofacts, pulled September 2026).

Lead and copper at the tap

In the sampling period ending December 2025, the 90th-percentile lead result at Oakwood Village MHP was 0 ppb, under both the current 15 ppb action level and the 10 ppb level that applies from 2027. A result of 0 means at least nine in ten of the homes sampled had no lead detected.

EPA has 6 sampling periods on file for Oakwood Village MHP since 2016, the first ending in 2016; no period was above 10 ppb.

Every water system has to inventory its service lines, the pipes from the main to each building. In the inventory Oakwood Village MHP sent EPA, 513 lines are counted.

Service lines in the inventory
MaterialLines
Lead0
Galvanized, needing replacement0
Unknown material0
Not lead513
All lines513

Systems sample taps in the homes most likely to have lead pipes or solder. The 90th-percentile result is the level nine in ten of the sampled homes were at or below. Lead comes mostly from service lines and house plumbing, not the source water, so a low result for the system does not clear an old house.

EPA's dashboard status for this inventory: reported all required service line types.

Source: EPA Safe Drinking Water Information System (SDWIS) lead and copper 90th-percentile results (EPA Envirofacts), sampling periods ending 2016 or later; EPA's service line inventory dashboard, Ohio's 2026 Q2 submission.

PFAS

The water Oakwood Village MHP buys is treated by Dayton Public Water System, so the results below are Dayton Public Water System's.

EPA's fifth national round of testing (UCMR 5) took 9 samples of the water entering the pipes of Dayton Public Water System in 2023 and measured 29 PFAS.

The highest PFOA or PFOS result, 10 ng/L, is at or above the federal limit of 4 ng/L that EPA set in 2024. Systems have until 2029 to comply, and in May 2026 EPA proposed letting systems apply for two more years. One sample over the limit is not a violation: compliance is judged on a running annual average.

The highest PFAS results were PFOS 10 ng/L, PFHxS 9.8 ng/L, and PFPeA 4.6 ng/L.

The highest PFOA or PFOS result was measured at Ottawa TP.

The system reported potential PFAS sources near its supply.

Ohio EPA's own statewide sampling tested 2 plants of Dayton Public Water System (latest sample February 2021). The highest result was PFHxS at 7.7 ppt (ppt is the same unit as ng/L), against Ohio's action level of 140 ppt. Those action levels are the ones Ohio EPA used for the survey; the 2024 federal limit for PFOA and PFOS is 4 ng/L.

Ohio EPA's current sampling status map lists 2 plants of Dayton Public Water System as sampled, most recently April 2026.

Highest PFOA and PFOS result, UCMR 5
CompoundHighest resultFederal limit
PFOAnot detected4 ng/L
PFOS10 ng/L4 ng/L

PFAS are the 'forever chemicals' from firefighting foam, plating shops and non-stick coatings. Results are for water leaving the plant, not your tap.

Source: EPA UCMR 5 occurrence data (final release, August 2026); Ohio EPA statewide PFAS sampling, 2019 to 2021, and its sampling status map.

Disinfection byproducts

Chlorine that disinfects water also reacts with organic matter to form byproducts. Two groups have federal limits: total trihalomethanes (TTHM, 80 µg/L) and five haloacetic acids (HAA5, 60 µg/L), judged on running yearly averages at each sampling site.

For TTHM, the average of Oakwood Village MHP's samples in 2019, the last year it was sampled, was 37.2 µg/L. The worst yearly average was 37.2 µg/L and the highest single sample was 43.5 µg/L, from 35 samples taken from 2012 to 2019.

For HAA5, the average in the last year sampled was 0 µg/L. The worst yearly average was 7.9 µg/L and the highest single sample was 17.3 µg/L, from 35 samples.

Disinfection byproducts in the distribution system
ByproductLimitLatest yearly averageWorst yearly averageHighest sampleSamples
TTHM80 µg/L37.2 µg/L (2019)37.2 µg/L43.5 µg/L35
HAA560 µg/L0 µg/L7.9 µg/L17.3 µg/L35

A yearly average of 0 means nothing was detected in that year's samples. EPA's file stops at 2019; Ohio EPA's Drinking Water Watch has newer results.

Source: EPA Six-Year Review 4 compliance monitoring data, 2012 to 2019, distribution-system samples (non-detects counted as zero).

Nitrate, arsenic and radioactivity

The water Oakwood Village MHP buys is treated by Dayton Public Water System, so the results below are Dayton Public Water System's.

Nitrate: the highest of 260 samples was 1.9 mg/L (as nitrogen), in 2019, the last year sampled. No sample was over the limit of 10 mg/L. Nitrate above 10 is unsafe for infants.

Arsenic was not detected in 31 samples (limit 10 µg/L).

Nitrate, arsenic and radioactivity in finished water, 2012 to 2019
ContaminantSamplesHighest resultLimitSamples over limit
Nitrate (as nitrogen)2601.9 mg/L10 mg/L0
Arsenic31not detected10 µg/L0

Measured in finished water: at the plant's entry points and in the distribution system; raw well and intake samples are left out. Non-detects count as zero.

EPA's file lumps the entry-point samples of all 2 plants of Dayton Public Water System together, so a result over a limit may come from a plant that serves a different part of town.

Source: EPA Six-Year Review 4 compliance monitoring data, 2012 to 2019, finished water of Dayton Public Water System.

Solvents and fuels

The water Oakwood Village MHP buys is treated by Dayton Public Water System, so the results below are Dayton Public Water System's.

EPA's file holds results for all six solvent and fuel compounds it checked. trichloroethylene (TCE) was detected in 1 of 98 samples, highest 1.06 µg/L (limit 5). Benzene, carbon tetrachloride, 1,2-dichloroethane, tetrachloroethylene, and vinyl chloride were not detected in 98 samples each.

Solvents and fuels in finished water, 2012 to 2019
CompoundLimitSamplesDetected inHighest resultSamples over limit
Benzene5 µg/L980 of 98not detected0
Carbon tetrachloride5 µg/L980 of 98not detected0
1,2-dichloroethane5 µg/L980 of 98not detected0
Trichloroethylene (TCE)5 µg/L981 of 981.06 µg/L0
Tetrachloroethylene (PCE)5 µg/L980 of 98not detected0
Vinyl chloride2 µg/L980 of 98not detected0

"Not detected" means the lab's result was below what its method can measure, not that the compound is absent. Non-detects count as zero in the highest-result column.

Source: EPA Six-Year Review 4 compliance monitoring data, 2012 to 2019, finished water of Dayton Public Water System.

Farm chemicals and metals

The water Oakwood Village MHP buys is treated by Dayton Public Water System, so the results below are Dayton Public Water System's.

EPA's file holds results for 8 of the nine herbicides and metals it checked. Detected: barium in 31 of 33 samples, highest 94.2 µg/L (limit 2,000). Not detected: atrazine in 18 samples, alachlor in 18 samples, chromium in 31 samples, cadmium in 31 samples, mercury in 22 samples, selenium in 28 samples, thallium in 22 samples.

Herbicides and metals in finished water, 2012 to 2019
SubstanceKindLimitSamplesDetected inHighest resultSamples over limit
AtrazineFarm chemical3 µg/L180 of 18not detected0
AlachlorFarm chemical2 µg/L180 of 18not detected0
ChromiumMetal100 µg/L310 of 31not detected0
CadmiumMetal5 µg/L310 of 31not detected0
BariumMetal2,000 µg/L3331 of 3394.2 µg/L0
MercuryMetal2 µg/L220 of 22not detected0
SeleniumMetal50 µg/L280 of 28not detected0
ThalliumMetal2 µg/L220 of 22not detected0

Non-detects count as zero in the highest-result column.

EPA's file lumps the entry-point samples of all 2 plants of Dayton Public Water System together, so a result over a limit may come from a plant that serves a different part of town.

Source: EPA Six-Year Review 4 compliance monitoring data, 2012 to 2019, finished water of Dayton Public Water System.

Bacteria in the pipes

From 2012 to 2019, 0 of 190 routine total coliform samples taken in the distribution system at Oakwood Village MHP tested positive (0%); in 2019, the last year on file, 0 of 24 did. E. coli was never found in the 190 samples tested for it.

A positive coliform test is a warning sign, not a violation by itself. E. coli is a sign that human or animal waste may have reached the water. Coliform counts are routine samples only; E. coli counts include repeat samples.

Source: EPA Six-Year Review 4 compliance monitoring data, 2012 to 2019, distribution-system presence/absence tests for total coliform and E. coli.

Fluoride

The Ohio Department of Health's report to the CDC (My Water's Fluoride) says Oakwood Village MHP buys its water from Dayton Public Water System, a system that adjusts the fluoride level to the recommended level for preventing tooth decay.

EPA's treatment table lists fluoridation among the steps at Dayton Public Water System, which treats the water Oakwood Village MHP buys.

Measured fluoride: 0.88 mg/L on average leaving the plants of Dayton Public Water System, which supplies Oakwood Village MHP, in 2019 (in the range dentists aim for); samples ran from 0.84 to 1 mg/L across 16 samples in 2012 to 2019.

The recommended level for preventing tooth decay is 0.7 mg/L; the federal limit is 4 mg/L. The treatment list is what each system registered with EPA and can lag a plant upgrade.

Source: CDC My Water's Fluoride (fluoridation status as reported by the Ohio Department of Health, fetched September 2026); EPA Safe Drinking Water Information System (SDWIS) treatment table; EPA Six-Year Review 4 compliance monitoring data, 2012 to 2019, entry-point fluoride samples.

Lithium

Lithium was not detected in 8 UCMR 5 samples at Dayton Public Water System, which supplies Oakwood Village MHP, last sampled in 2023 (the method reports from 9 µg/L).

Lithium is not regulated. EPA's draft health reference level is 10 µg/L, and it occurs naturally in deep groundwater, so well systems in the northwest run highest.

Source: EPA UCMR 5 occurrence data (final release, August 2026), samples from 2023 to 2025.

Algal toxins

The water Oakwood Village MHP buys is treated by Dayton Public Water System, so the results below are Dayton Public Water System's.

Ohio EPA tests for microcystin, a toxin that harmful algal blooms can release, in raw water at the intake and in treated water.

No microcystin was detected in the 164 raw-water samples.

Microcystin was never detected in treated water (199 samples).

In all, 363 samples from 2016 to 2026, the latest on May 19, 2026.

Microcystin results
WaterSamplesDetectionsHighest result
Raw water, at the intake1640not detected
Treated water1990not detected

The ten-day advisory levels for treated water are 0.3 µg/L for children under six and 1.6 µg/L for everyone else. Any detection at the intake triggers more frequent testing until two clean weeks.

Source: Ohio EPA public water system harmful algal bloom monitoring, 2016 to present (HAB data, fetched September 2026).

How well the service area is mapped

EPA estimated the service area of Oakwood Village MHP with a computer model rather than drawing it from the utility's map, so its edges are approximate.

Source: EPA Service Area Boundaries; resident estimate by this atlas from ZIP-code overlap.

On the map

Show this system's territory on the map — 1 ZIP code in all.

Sources

U.S. EPA SDWIS and Community Water System Service Area Boundaries (v3, 2026), Ohio EPA primacy data, 2020 census blocks: the system serving most residents, traced through purchases to the treating utility; Ohio EPA 2023 Sewer and Water Rate Survey (Ohio State, May 2025) for household bills; Ohio EPA DEFA loan awards since 2016 for the loans paragraph · EPA SDWIS · EPA service area boundaries · Ohio EPA drinking water · Ohio EPA rate survey

EPA's own record for this system: Enforcement and Compliance History report for OH5703715 (EPA ECHO).

Quick answers

Where does Oakwood Village MHP get its water?

Oakwood Village MHP buys its water from Montgomery County Water Services 2.

How many people does Oakwood Village MHP serve?

Oakwood Village MHP serves about 1,500 people.

Cite this page

Cite this page as:

Cracked Buckeye, "Oakwood Village MHP · OH5703715", https://crackedbuckeye.com/water/OH5703715/, built 2026-10-31, accessed [date].

How to cite · Report a correction · Built 2026-10-31